BRODA® PRO-TEK-TOR Siding Log Timber (SLT)

BRODA® PRO-TEK-TOR Siding Log Timber (SLT)

BRODA ® PRO-TEK-TOR™ Siding, Log & Timber (SLT)
Water borne, natural oil, penetrating wood finish, offering excellent mildew resistance, UV protection and water repellency. Enhances natural beauty of wood and imparts a beautiful oiled appearance. When applied correctly will not peel, crack or blister.

Please call, toll-free at 1-888-311-5339 or email info@cbrproducts.com if you have ANY questions about BRODA ® PRO-TEK-TOR™ SLT


Label Instructions This link leads to a PDF file of the instructions from the can, in case the label has been damaged or you want to print them at a larger size. (Aussi en Français!)


BRODA® Colour Selector Click to see the range of more than 50 stock BRODA® colours. For custom colour tinting, contact us.

PRO-TEK-TOR APPLICATION FAQ’s Some more questions and answers about BRODA® low-VOC wood stain


Technical Data and Material Safety Data Sheets

MSDS: PRO-TEK-TOR Siding-Log-Timber.pdf
USAGE: PRO-TEK-TOR SLT.pdf


Where to use
PRO-TEK-TOR™ SLT

For vertical and protected
wood surfaces
Wood staining tools Tools and equipment
you will need
How to prepare wood for staining Preparing The Surface
for BRODA ® Coatings
  Restoring Weathered Wood
  Mixing BRODA ®
PRO-TEK-TOR ™ SLT

how to apply wood stain low-VOC Applying BRODA ®
PRO-TEK-TOR SLT

Cleaning Up with
BRODA ® Coatings
Video: Maintenance with
BRODA ® Coatings

BRODA® PRO-TEK-TOR SLT - Where To Use It
BRODA ® PRO-TEK-TOR Siding–Log–Timber (SLT) Natural Oil Wood Finish is a water borne, natural oil, penetrating wood finish. It can be applied on dry or unseasoned wood with up to a 30% moisture level. Broda SLT offers excellent mildew resistance, UV protection and water repellency. Use on vertical and protected wood surfaces, like siding, wall shingles, log walls, timber frames, soffiting, and trim. PRO-TEK-TOR SLT enhances the natural beauty of wood and imparts an oiled appearance. When applied correctly it will not peel, crack or blister.

Coverage: Rough surfaces: 150 - 300 sq. ft. / gallon / coat. Sanded, smooth surfaces: 250 - 400 sq. ft. / gallon / coat. Coverage will depend on wod species, texture and/or porosity.



Tools & Equipment You Will Need, BRODA® PRO-TEK-TOR SLT
Brush: Use a natural bristle brush (ie. Corona Oil-Stain-It) a or an applicator pad. No reduction necessary.
Roller: Use a 10mm – 20mm roller cover.
Spray-Airless: Pressure: 2000 psi Tip:  .013 -- .015 
Spray-HVLP: Tip: Standard needle
Depending on the job, a power washer, a grinder and a good quality sander may also be required. Tape, tarps, trays and some rags will always come in handy.


 


Preparing The Surface for BRODA® Coatings
Remove all existing paints, coatings, mildew, wax, oil, dirt and deteriorated substrate. 
(Replace all deteriorated substrate as required)
Rough Wood Surfaces:  Power wash at 500 psi.
Smooth Wood Surfaces:  Sand to 80 grit. 
New wood: Remove all mill glaze. (the glossy surface on planed or new lumber surfaces)
Pressure Treated Wood:  Test the absorbency of the wood by sprinkling water on the surface. If the water penetrates into the wood quickly, the wood is ready to finish. If the water beads up or does not penetrate, allow the wood to weather and test for absorbency again. Do not sand pressure treated lumber. Due to the green or brown tone of many brands of pressure treated lumber, the colour of the BRODA ® PRO-TEK-TOR SLT may look different from the colour selected. Always test for colour and appearance in an inconspicuous area.
Previously Stained Wood: BRODA ® PRO-TEK-TOR SLT may be applied over existing well weathered semi-transparent stains, however, the colour of the existing stain may be visible through this finish. Remove all surface contamination by sanding, power washing or with a wood cleaning/restoration product.

Removing Mildew: If after cleaning, the surface appears dirty, suspect mildew. Remove mildew before painting with a solution of 1 pint bleach and 1 gallon water. Apply the solution and scrub the area. Allow bleach solution to remain on the surface for 10 minutes. Rinse thoroughly with water until there is no bleach odor. Apply diluted acid based wood cleaner to neutralize bleach. Rinse well until sudsing no longer persists. Wear protective eyewear, rubber gloves, and
protective clothing. Quickly wash off any of the cleaning solutions which come in contact with your skin. Do not add detergents or ammonia to the bleach/water solution. Apply appropriate patching and filling materials to cracks, nail holes
and other surface imperfections. Filled areas may take BRODA ® PRO-TEK-TOR SLT differently than bare wood. Do not get caulk or primer on areas to receive BRODA ® PRO-TEK-TOR SLT. (BRODA ® PRO-TEK-TOR SLT will appear different over caulk or primer.) Optimum wood surface pH is slightly alkaline. 


Restoring Weathered Wood
To clean and brighten weathered wood, we recommend using X180 Weathered Wood Restorer. Once you have power washed the surface, apply the X180 as per manufacturer's directions. Make sure all landscaping and surfaces you DON’T want restored are covered with tarps top protect from overspray. Do not apply in direct sunlight or when it is too hot out, because the X180 will only work when it is wet.
Let it sit for about an hour or so, then rinse well. There must be no soap bubbles in the water when all the X180 is rinsed off. Let surface dry to slightly damp.


Mixing BRODA® BRODA® PRO-TEK-TOR SLT
Applying BRODA® PRO-TEK-TOR SLT is easy, but you want to make sure it’s well mixed first. Open the can and use a stir stick to loosen up the pigment. Pour into another container and scrape any remaining pigment off the bottom of the original container.

Keep mixing back and forth until you’re sure you’ve got all of the pigment mixed in. Intermix same colours from the same job together.


Applying BRODA® BRODA® PRO-TEK-TOR SLT
Apply 1st coat of Broda SLT as a heavy coat and work into the wood surface until
recommended coverage is achieved. Spread any puddles or runs.

If the wood surface is warm to the touch, dilute Broda SLT up to 10% with cold water or dampen the wood surface prior to application.

Apply 2nd coat of Broda SLT after first coat has dried for the recoat period recommended above. Fully saturate the wood surface and achieve the recommended coverage. Spread any puddles and runs. Apply third coat of Broda SLT after the 2nd coat has dried for the recoat period recommended above. Apply as an even application. Spread any puddles or runs.
Important: Do not apply in direct sunlight. Apply from bottom to top of project. Apply up and down on vertical siding and posts.
Apply side to side on horizontal siding and logs.
Drying Time @ 50% Relative Humidity: 
Touch:  @5C : 8 hours  @12C: 5 hours  @20C: 2 hours
Recoat:  @5C:  48 hours  @12C: 24 hours  @20C: 12 hours
Temperature and humidity dependent. Air and surface temperature should not drop below 1C for 48 hours after application.
Coats: 2 coats of tinted SLT  followed by 1 coat of SLT or SLT+ Clear UV Top Coat 
are necessary to achieve the selected colour.


Cleaning Up with BRODA® Coatings
Clean spills and spatters immediately with soap and warm water. Clean hands and tools immediately after use with soap and warm water.  After cleaning, flush spray equipment with mineral spirits to prevent rusting of the equipment if  recommended by the manufacturer. Follow manufacturer’s safety recommendations when using mineral spirits. 
If you’ve been staining all day, it’s probably a good idea to clean yourself up, too. Again, soap and water is best.
Now that you’re all done, time to relax, West-Coast BRODA® Style!
To find out more about our natural oil stain, acrylics, urethanes and low-VOC paint, visit http://www.brodacoatings.com or give us a call, toll-free at 1-888-311-5339

CAUTIONS: Do not use on roofs. Do not apply at temperatures below 1C. Not for use on exposed horizontal surfaces where water may collect. Use Broda Pro-Tek-Tor Deck – Rail Natural Oil Wood Finish for decks, fences, railings, etc.
Water-based or water-borne coatings react with metal. All metal contamination and staining must be removed prior to applying Broda. After application of Broda, avoid contact with metal. Treating wood with CBR Iron Shield prior to applying Broda reduces staining due to metal contamination.
LABEL CAUTIONS: Use only in well ventilated conditions. Always wear respiratory protection (NIOSH approved). If you experience headaches or dizziness, increase fresh air or leave the area. Do not take internally. May irritate eyes. Do not get in eyes. May irritate skin. Do not get on skin or clothing. Wash hands after using.  Keep container closed when not in use. Do not transfer contents to other containers for storage. 
FIRST AID TREATMENT: If in eyes, rinse with water for 15 minutes. If on skin, rinse well with water.  If swallowed, call a Poison Control Centre or doctor immediately. Do not induce vomiting. 
KEEP OUT OF REACH OF CHILDREN. The information and recommendations set forth in this Product Data Sheet are based upon tests conducted by or on behalf of CBR Products (a division of Canadian Building Restoration Products Inc.).
Such information and recommendations set forth herein are subject to change and pertain to the product offered at the time of publication. Consult your CBR Products representative to obtain the most recent Product Data Sheet.


BRODA® Maintenance Video